RouterReset

Buffalo WZR-G108

The Buffalo WZR-G108 router has 54mbps WiFi, 4 100mbps ETH-ports and 0 USB-ports. It also supports custom firmwares like: dd-wrt

Quick links:
Default password/Login
Login instructions
User Manuals
Flashing Custom Firmwares

Table of Contents

WZR-G108 router specifications

System specs
Cpu: 264 MHz
RAM: 32 MiB
Flash: 8 MiB
Custom firmwares: dd-wrt
Connectivity
WiFi: 54mbps (bg)
WiFi bands: 2.4GHz
WiFi throughput: n/a
WAN: 1 100mbps port
ETH: 4 100mbps ports
USB-ports: 0

Hard reset instructions for Buffalo WZR-G108

If your WZR-G108 router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist. Other scenarios where you might want to reset your router is if you've forgotten the password or misconfigured it and can't get access anymore.
Your can reset your Buffalo WZR-G108 in the following way(s):

The 30-30-30 reset

There are no specific instructions for this model yet, but you can always do the 30-30-30 reset as follows:
  1. When router is powered on, press the reset button and hold for 30 seconds. (Use a paper clip or something sharp)
  2. While holding the reset button pressed, unplug the power of the router and hold the reset button for 30 seconds
  3. While still holding the reset button down, turn on the power to the unit again and hold for another 30 seconds.

This process usually works for resetting any router to it's factory setting.
Note: It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Default factory settings for Buffalo WZR-G108

If you have performed a reset of your WZR-G108 device or not changed the defaults, you should be able to access it with the following settings:

Default Network name (SSID): 000D0BXYXYXYXYXYXY
Default Gateway IP: 192.168.11.1 Buffalo login instructions
Default username: root Buffalo router default password list
Default subnet mask: 255.255.255.0
Default DNS server: 192.168.11.1
Note: If you are using the default settings you should change them to increase security and prevent unathorized access to your network.

How to login to the WZR-G108

To login to the WZR-G108 router and change the settings, you can follow these steps:

  1. Make sure you are connected to the router's network, either by Wi-Fi or ethernet cable.
  2. Open your browser and visit http://192.168.11.1
  3. You should be prompted with a login dialogue.
  4. Enter the username: root and if it requires a password, leave it empty or try with admin/password
    Note: If you have already changed the password use that instead.
  5. You will now be logged in. If you haven't yet changed the defaul password, we recommend that you change it first thing you do after logging in.

If these instructions don't work for your router, you can always try a factory reset to get the default, or try some other common Buffalo credentials, as they can usually be shared across models/variants.

WZR-G108 Firmwares

Staying up to date with the latest firmware is a good idea to keep your router even more secure from various security flaws.
If you want to squeeze a little bit of extra functionality out of your router, consider flashing an open-source firmware like dd-wrt, openWRT or LEDE. Flashing a custom ROM can greatly increase the stability and functionality of your old router.
Following are the firmwares that we have identified existing for the Buffalo WZR-G108:

Flashing dd-wrt on the Buffalo WZR-G108

We haven't find any specific instructions for flashin dd-wrt onto the Buffalo WZR-G108, but you can read the Installation guide over at dd-wrt to get a clue on how to proceed (As this model is listed as supported).
Note: Always make sure to read the wiki and howtos of dd-wrt before doing any flashing.

Similar routers

WZR-G240
2700HG-B
WZR-HP-G54
Report error on page
(If info is incorrect)